1.Change The Water And Clean The Tank
Recommended. Clean the water tank and replace the circulating water once a week.
Note: Before the machine works, please make sure the laser tube is filled with circulating water.
The quality and temperature of the circulating water directly affects the service life of the laser tube of the laser engraver. It is recommended to use pure water and to keep the water temperature below 35°C. If it exceeds 35°C, the circulating water needs to be replaced. (It is recommended that users choose one cooler or use two water tanks).
Clean the water tank: first turn off the power, unplug the inlet pipe, let the water in the laser tube flow into the water tank automatically, open the water tank, take out the pump and remove the dirt on the pump. Clean the water tank, replace the circulating water, restore the water pump to the tank, insert the water pipe connected to the water pump into the water inlet, and sort out all the joints. Turn on the power of the pump alone and run it for 2-3 minutes (so that the laser tube is filled with circulating water).
If the winter temperature is very low in northern areas, it may cause the water inside the laser tube to freeze. You can add antifreeze to prevent the water from freezing and causing the laser tube to break.
2. Fan Cleaning
Long-term use of the fan will accumulate a lot of solid dust in the fan, which makes the fan produce a lot of noise, and is also not conducive to exhaust and deodorization. When the fan suction power is insufficient and the exhaust is not smooth, first turn off the power, remove the inlet and outlet ducts on the fan, remove the dust inside, then turn the fan upside down and pull the internal blades until it is clean, then install the fan.
3.The Lens Cleaning
(It is recommended to clean before work every day and the equipment must be turned off)
There are three reflectors and one focusing lens on the engraving machine (No. 1 reflector is located at the emission port of the laser tube, which is the upper left corner of the machine, No. 2 reflector is located at the left end of the beam, and No. 3 reflector is located at the fixed part of the laser head. At the top of the laser head, the focusing lens is located in the adjustable mirror barrel at the lower part of the laser head). The laser is reflected and focused by these lenses and then emitted from the laser head. The lenses can easily get dust or other contaminants, causing loss of laser light or damage to the lenses. When cleaning lenses #1 and #2, do not remove the lenses. Simply place a lens wipe dipped in cleaning solution carefully along the center of the lens. Rotate the edge wipe. lens #3 and focus lenses need to be removed from the frame and wiped in the same way, wiped and then put back in place.
Note: 1. wipe the lens gently, not to damage the surface coating; 2. wipe the process to hold lightly to prevent falling; 3. when installing the focusing lens, be sure to put the concave side down.
4.The Cleaning Of The Guide
(It is recommended to clean once every half month, close the operation)
Guide rail and linear axis is one of the core components of the equipment, its function is to play a guiding and supporting role. In order to ensure the high processing accuracy of the equipment, the requirements of the guide rail and linear have high guiding accuracy and good stability of movement. During the operation of the equipment, due to the large amount of corrosive soot generated when processing parts, these soot will be deposited on the surface of the guide rail and linear axis for a long time, which has a great impact on the processing accuracy of the Sulpfun laser engraver and will form corrosion points on the surface of the linear axis of the guide rail, shortening the service life of the equipment. In order to make the equipment work normally and stably and ensure the processing quality of the products, the daily maintenance of the guide rails and linear axes must be done carefully.
Note: Please be prepared to clean the tools of the guide rail - dry cotton cloth, lubricant
The guide rails of sculpfun s10 laser engraver are divided into linear guide rails and roller guide rails. In YM series, linear guide is used in X direction and roller guide is used in Y direction.
Clean the linear guide: first move the laser head to the far right (or left), find the linear guide as shown above, wipe it with a dry cotton cloth until it is shiny and dust-free, and add a little lubricant (sewing machine oil can be used, do not use machine oil), slowly push the laser head from one side to the other several times to make the lubricant evenly distributed.
Clean the roller guide. Move the beam to the inside, open the end cover on both sides of the machine, find the guide rail as shown in the picture above, wipe both sides of the guide rail with a dry cotton cloth where it touches the roller, then move the beam and clean the rest.
5. Tightening Of Screws And Couplings
After the motion system works for a period of time, the screws and couplings at the motion connection will loosen and affect the smoothness of the mechanical motion. Therefore, during the operation of the machine, pay attention to observe whether there is any abnormal noise or abnormal phenomenon in the transmission parts and find out the problem in time. Stability and maintenance. Meanwhile, after the machine is used for a period of time, the screws should be tightened one by one using tools. The first tightening should be about one month after the use of the equipment.
6.The Inspection Of The Optical Path
The light path system of Sculpfun S30 Pro Max laser engraving machine is completed by the reflection of the reflector and the focus of the focusing mirror. In the light path, the focusing mirror does not have the problem of deflection, but the three mirrors are fixed by the mechanical part, the possibility of deflection is relatively Although there is no offset under normal circumstances, users are advised to check whether the light path is normal before each work.
